Important note — emergency callsThe e3300 is not designed for making emergencycalls when the mains power fails. So you shouldmake alternative arrangem
Caller DisplayIf you subscribe to this feature from your service provider,you can see the phone numbers of your callers on thedisplay, before you answ
Using a multi-handset systemIf you have an e3300 Twin or Triple system, you alreadyhave two or three handsets registered to your base unit.You can reg
To shuttlebetween twocallsWhen you have both an outside call and anintercom call in progress, you can shuttle fromone to the other, like this:◗Press t
To register anew handsetto your baseunitThe handset(s) supplied with your base unit should notneed to be registered; only additional ones you haveboug
To register toa differentbrand of baseunitYour e3300 can be registered to any GAP-compatiblebase unit; or your can register other GAP-compatiblehandse
Ringer volumeand melodyThe handset has eight ringer volume levels, including 0for off; and eight ringer melodies. With the volume setto 0, the handset
To clear allmemoriesThis is a way of clearing all stored numbers atonce, from the memory locations and the LastNumber Redial memories. If you have set
Ringer volumeand melodyThe base unit has eight ringer volume levels, including0 for off; and eight ringer melodies. With the volume setto 0, the base
To bar certain types of call1 Press the PROG button then 2 2 12 Key in the handset number (1 to 6)3 Use the ▲ or ▼ button to set:0 no outside calls (i
Indirect NetworkYou can use this feature if you make some of your callsvia a different network from the one that supplies yourexchange line. By using
Where to find itBefore you can use the handset to make callsyou will need to fit and fully charge thebatteries, as described on pages 4 and 5.Please r
Troubleshooting!The e3300 must be serviced by trained engineers.NEVER attempt any repairs or adjustments yourself— you could make the problem worse an
“There is inter-ference andnoise on theline.”Move the handset closer to the base unit, or to adifferent position.Try moving the base unit so that it’s
Batteries“The handset‘sbattery pack isrunning lowwithinan hour ortwo.”Before you first used the handset, you should have left iton the base unit or ch
Cleaning and care◆Do not clean any part of your e3300 with benzene,thinner or other solvent chemicals — this may causepermanent damage which is not co
Technical detailsStandard Digital Enhanced CordlessTelecommunications (DECT)Frequency range 1.88 to 1.9 GHz (bandwidth = 20 MHz)Channel bandwidth 1.72
N New Call tone, 19notebook, 12O ‘Out of range’ warning, 6P paging handsets, 19pause, 38, 42PBX compatibility, 38–39,42PIN codebase unit, 27han
CONTENTSRead these notes first 3Choosing a site for the base unit andcharger pod 3Radio signals between handset andbase unit 3Mains power connection 3
Customising your base unit 27The base unit’s PIN code 27Emergency numbers 27Ringer volume and melody 28Call barring 28Date and time 30To clear all Cal
Installation and set-up41354Choose a suitable site for thebase unit See page 3Plug the mains adapter into a230 V AC, 50 Hz mains socket,with the switc
Before you startElectricalsafety◆DO NOT let the base unit or charger pod get wet.Electrical equipment can cause serious injury if usedwhile you are we
Making and answering callsTo make a call1 Key in the telephone numberIf you make a mistake, press the HANG UP/Cbutton to clear one digit at a time fro
Memory diallingYou can store up to 20 phone numbers in memory.Each number can have up to 24 digits. The 20 memorylocations are numbered 01 to 20.To st
To delete astorednumber1 Press the MEMORY button2 Press the ▲ or ▼ button until the numberyou want to delete is displayed3 Press and hold the HANG UP/
Kommentare zu diesen Handbüchern